Most of the home security systems are very expensive. With the help of this project, an inexpensive burglar alarm system can be implemented.

Circuit Diagram

Components Required

LM358 – 1 IR Transmitter or IR LED – 1 Photo Diode – 1 10 KΩ – 1 150Ω – 1 10 KΩ POT – 1 Buzzer – 1

Component Description

LM358

It is a dual Op Amp IC. It consists of two independent operational amplifiers that can be used separately. It is commonly used in all op amp circuits, transducer amplifiers, active filters, general signal conditioning and DC gain blocks. LM358 DataSheet

IR Transmitter

Infrared or IR is a range of light frequencies that have longer wavelength than visible light. Hence, they are not visible to human eye. An IR transmitter or IR LED is a device that emits infrared light.

Photo Diode

A photo diode is a device that converts light to electrical current. It is basically a PN junction that operates in reverse bias condition. When light falls on the photo diode, a reverse bias current flows in the junction that is proportional to the luminescence of the light.

Buzzer

It is an alarming device that makes a loud sound when current flows through it.

Circuit Design of Burglar Alarm System

The IR transmitter or IR LED is connected to a current limiting resistor of 150Ω and connected to supply. It is placed at the maximum possible range from photo diode. The cathode of the photo diode is connected to supply while anode is connected to 10KΩ resistor. Other end of the resistor is connected to ground. The anode terminal of the photo diode is also connected to pin 5 of LM358 op amp, which is the non-inverting terminal. Wiper of the 10KΩ POT is connected to the inverting terminal i.e. pin 6 of LM358 while the other two terminals of the POT are connected to Vcc and ground. Pins 8 and 4 of LM358 are supply pins. They are connected to Vcc and ground respectively. The output of the op amp is taken at pin 7. One terminal of the buzzer is connected to pin 7 of LM358 while the other terminal is connected to Vcc.

Working

The aim of this project is to implement a simple Burglar Alarm System that can detect an unauthorized entry by a burglar. All the connections are made as per circuit diagram. The working of the circuit is as follows. LM358 is configured to work as comparator in this project. When the system is powered on, the IR transmitter or IR LED emits infrared light. This light falls on the surface of the photo diode. As it is connected in reverse bias fashion, when the light falls on it, it conducts and current flows through it. Since it is connected to the non-inverting terminal (pin 5) of the op amp, output of the op amp comparator will be high. As the buzzer is connected between Vcc and output of op amp, no alarm is made. When an intruder or a burglar enters the gap between the IR transmitter and photo diode, the light falling on the photo diode is interrupted and it doesn’t conduct. As a result, the input at non-inverting terminal (pin 5) is less than the input at inverting terminal (pin 6). Hence, the output of the comparator is low. This will trigger the buzzer and a loud alarm is made. NOTE

The range of the system is very less and is dependent on the transmitter power. The range of IR detection can be extended by using converging lens. Another way to increase the range is to implement a series of photo diode. Instead of using IR transmission and detection, a high intensity LASER light and an LDR can also be used to implement the same circuit.

Burglar alarm can also be implemented in different ways.Some of the burglar security systems were as follows.

Arduino and GSM Home Security System

Here arduino board along with GSM Provides security to the home.When any intruder enters home this system sends a call to the owner using GSM.

Read More

PIR Sensor Based Security System

This is another burglar alarm system using PIR sensor.This system will have a PIR sensor which detects Intruder. When no one present in the house switch this system and leave it.When any intruder is detected it sounds an alarm.

Read More

Super sensitive intrude alarm

This alarm uses IR sensor and infrared Led to detect the intruder. This uses 555 timer and comparator. When the intruder enters home, this circuit produces the sound using a speaker.

Read More     I am doing this a project in schoola and was wondering is there anything missing from the circuit diagram and the breadboard Do you have the pot set to a certain resistance and is there a certain distance required between the transmitter and reciever? any help would be greatly appreciated. Thanks Comment * Name * Email * Website

Δ

How To Make Best Burglar Alarm Circuit  - 13How To Make Best Burglar Alarm Circuit  - 64How To Make Best Burglar Alarm Circuit  - 22How To Make Best Burglar Alarm Circuit  - 98How To Make Best Burglar Alarm Circuit  - 32How To Make Best Burglar Alarm Circuit  - 63How To Make Best Burglar Alarm Circuit  - 49How To Make Best Burglar Alarm Circuit  - 75How To Make Best Burglar Alarm Circuit  - 82How To Make Best Burglar Alarm Circuit  - 68How To Make Best Burglar Alarm Circuit  - 94